September 4, 2020 | Catalyst palladium

The origin of a common compound about 887919-35-9

This compound has a wide range of applications. It is believed that with the continuous development of the source of the synthetic route,887919-35-9,Bis(di-tert-butyl(4-dimethylaminophenyl)phosphine)dichloropalladium(II),its application will become more common.

A common heterocyclic compound, 887919-35-9,Bis(di-tert-butyl(4-dimethylaminophenyl)phosphine)dichloropalladium(II), its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route. 887919-35-9

887919-35-9, Step 14-6, Preparation of tert-butyl N-{3-[(4-{4-[2-cyano-4-(trifluoromethyl)phenyl]piperazin-1-yl}-2′-ethoxy-[1,1′-biphenyl]-3-yl)formamido]propyl}carbamate To a mixture of tert-butyl N-{3-[(5-bromo-2-{4-[2-cyano-4-(trifluoromethyl)phenyl]piperazin-1-yl}phenyl)formamido]propyl}carbamate (20.0 mg, 0.0328 mmol), 2-ethoxyphenylboronic acid (10.9 mg, 0.0657 mmol), Pd[t-Bu2P(4-NMe2C6H4)]2Cl2) (9.2 mg, 0.013 mmol), and K2CO3 (27.2 mg, 0.197 mmol) in a sealed tube was added dioxane (2 mL) and H2O (0.2 mL). The resulting mixture was degassed with N2 for 10 min and stirred at 100 C. for 30 min. The mixture was concentrated and purified by C18 reversed phase column chromatography to give the title compound (18.5 mg, 87% yield) as a white solid. LCMS (M+H)+=652.5.

Reference£º
Patent; Crinetics Pharmaceuticals, Inc.; HAN, Sangdon; ZHU, Yunfei; KIM, Sun Hee; ZHAO, Jian; WANG, Shimiao; (146 pag.)US2019/367481; (2019); A1;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

A new synthetic route of (2,2¡ä-Bipyridine)dichloropalladium(II)

This compound has a wide range of applications. It is believed that with the continuous development of the source of the synthetic route,14871-92-2,(2,2¡ä-Bipyridine)dichloropalladium(II),its application will become more common.

A common heterocyclic compound, 14871-92-2,(2,2¡ä-Bipyridine)dichloropalladium(II), its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route. 14871-92-2

First, 63.6 mg (0.2 mmol)Of compounds 111-5 and 32.2 mmol (0.6 mmol)Of methanol was added to a mixture of 30 ml of anhydrous methanol and tetrahydrofuran(Volume ratio of 1: 1)Argon protection,After stirring at room temperature for 1.5 h,Followed by the addition of 66.4 mg (0.2 mmol) of cis-dichloro-1,1′-bipyridyl palladium (II)Continue to argon protection,Stirring at 25 C for 14 h,After the reaction,The resulting solid was purified by column chromatography,Get the target product,Weight 93.8 mg, yield: 85%., 14871-92-2

Reference£º
Patent; Changchun Institute of Applied Chemistry, Chinese Academy of Sciences; Wang, Zhiyuan; Liu, Bo; Qiao, Wenqiang; (34 pag.)CN103483391; (2016); B;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

The origin of a common compound about 53199-31-8

This compound has a wide range of applications. It is believed that with the continuous development of the source of the synthetic route,53199-31-8,Bis(tri-tert-butylphosphine)palladium,its application will become more common.

A common heterocyclic compound, 53199-31-8,Bis(tri-tert-butylphosphine)palladium, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route. 53199-31-8

Example 29 Preparation of 5-(4-{3-[3-(4-fluoro-phenyl)-5-oxo-1,5-dihydro-[1,2,4]triazol-4-yl]-propenyl}-phenyl)-furan-2-carbaldehyde (compound 44) This example describes the synthesis of common ligand mimics of the invention containing a linker group following the reaction scheme shown in . Compound numbers correspond to the numbers in the figure. The compounds 4-allyl-5-(4-fluoro-phenyl)-2,4-dihydro-[1,2,4]triazol-3-one (compound 42, 500 mg, 2.28 mmol) and 5-(4-bromo-phenyl)-furfural were mixed in dioxane (10 ml), followed by the addition of diisopropylethylamine (0.795 ml, 4.56 mmol). Bis(tri-tert-butylphosphine) palladium (56 mg, 0.109 mmol) was added to the reaction mixture, which then was stirred at a temperature of 90 C. for a period of 1 hour. Volatiles were removed in vacuo, and the residue was diluted in 0.2 N HCl solution, followed by extraction with ethyl acetate. Combined organic layers were dried over MgSO4, filtered, and concentrated in vacuo. The crude product was purified by flash chromatography (gradient 7:3 to 9:1 ethyl acetate/hexanes+0.5% MeOH) to give 5-(4-{3-[3-(4-fluoro-phenyl)-5-oxo-1,5-dihydro-[1,2,4]triazol-4-yl]-propenyl}-phenyl)-furan-2-carbaldehyde (compound 44, 375 mg, 42%). 1H NMR (300 MHz, CDCl3) delta 4.55 (d, J=4.7, 2H), 6.31 (td, J=3.2, 16.0, 1H), 6.44 (d, J=16.0, 1H), 6.84 (d, J=3.7, 1H), 7.18 (dd, J=8.5, JHF=8.5, 2H), 7.32 (d, J=3.7, 1H), 7.40 (d, J=8.3, 2H), 7.61 (dd, J=8.5, JHF=5.2, 2H), 7.76 (d, J=8.3, 2H), 9.64 (s, 1H), 10.56 (s, 1H); 13C NMR (300 MHz, CDCl3) delta 43.8, 107.9, 116.3 (d, JCF=22), 123.2, 124.4, 125.6, 127.1, 128.7, 130.3 (d, JCF=9), 132.3, 137.1, 147.0, 152.2, 155.7, 158.9, 164.1 (d, JCF=250), 206.6; MS m/s 389.96 (M+1).

Reference£º
Patent; Yu, Lin; Dong, Qing; Pierre, Fabrice; Chang, Edcon; Lang, Hengyuan; Qin, Yong; Fang, Yunfeng; Hansen, Mark; Pellecchia, Maurizio; US2004/9526; (2004); A1;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

Downstream synthetic route of (2,2¡ä-Bipyridine)dichloropalladium(II)

With the complex challenges of chemical substances, we look forward to future research findings about (2,2¡ä-Bipyridine)dichloropalladium(II),belong catalyst-palladium compound

As a common heterocyclic compound, it belongs to quinuclidine compound,Quinuclidine-4-carboxylic acid hydrochloride,40117-63-3,Molecular formula: C8H14ClNO225,mainly used in chemical industry, its synthesis route is as follows.,14871-92-2

[Pd(bpy)Cl2] (0.10 g, 0.30 mmol) was suspended in water (4 mL). Lactic acid (0.03 g, 0.28 mmol) and 1 M NaOH (0.60 mL) were dissolved in water (10 mL) and then added to the mixture, which was heated under reflux at 150 C with continuous stirring until a clear yellow solution was obtained. The solution was filtered and acetone (10 mL) was added to the solution. The reaction mixture was cooled to 4 C for a long time (2 months), resulting yellow crystals of complex 5. Yield: 33%. m.p.: 250 C. Elemental Anal. Calc. for C13H13ClN2OPd (355.10): C, 44.0; H, 3.7; N, 7.9. Found: C, 44.1; H, 3.6; N, 7.8%. IR (KBr, numax/cm-1): 1634 s, nu(CO); 1621 s, nu(CC); 1496 m, 1443 s, nu(CC,CN). Far-IR (Nujol, numax/cm-1): 333 m, nu(Pd-Cl); 285 m, nu(Pd-C); 243 m, nu(Pd-N). 1H NMR (CDCl3, delta/ppm): 2.40 (s, 3H, c), 3.01 (s, 2H, a), 7.61 (m, 2H, 5,5?), 8.02 (m, 4H, 3,3? and 4,4?), 9.31, 9.51 (2d, 2H, 6,6?).

With the complex challenges of chemical substances, we look forward to future research findings about (2,2¡ä-Bipyridine)dichloropalladium(II),belong catalyst-palladium compound

Reference£º
Article; Balboa, Susana; Carballo, Rosa; Castineiras, Alfonso; Gonzalez-Perez, Josefa Maria; Niclos-Gutierrez, Juan; Polyhedron; vol. 50; 1; (2013); p. 512 – 523;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

New downstream synthetic route of 52522-40-4

This compound has a wide range of applications. It is believed that with the continuous development of the source of the synthetic route,Tris(dibenzylideneacetone)dipalladium-chloroform,52522-40-4,its application will become more common.

A common heterocyclic compound, 52522-40-4,Tris(dibenzylideneacetone)dipalladium-chloroform, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route. 52522-40-4

52522-40-4, General procedure: 0.0813 g (0.4637mmol) of TMQ, 0.1671 g (1.159 mmol) of dmfu and 0.2000 g (0.1932 mmol) of [Pd2(DBA)3. CHCl3] were dissolved under inert atmosphere (Ar) in 30 ml of anhydrous acetone. The mixture was stirred for 60 m and eventually treated with active charcoal for 5/10 min and filtered on celite filter. The resulting yellow solution was dried under vacuum and the residual treated with diethyl ether, filtered, washed with diethyl ether in excess and dried under vacuum. 0.1104 g (yield 67percent) of the title compound was obtained as pale yellow microcrystals.

Reference£º
Article; Canovese; Visentin; Biz; Scattolin; Santo; Bertolasi; Journal of Organometallic Chemistry; vol. 786; (2015); p. 21 – 30;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

The origin of a common compound about 14871-92-2

14871-92-2, General procedure: Palladium(II) chloride (PdCl2), 2,2?-bipyridine (bipy), 1,10-phenanthroline (phen), thiourea (TU, 1), N-methylthiourea (meTU, 2), N-buthylthiourea (buTU, 3), N,N?-diethylthiourea (dietTU, 4) and N,N?-dibuthylthiourea (dibuTU, 5) were purchased as pure reagents at AG, from Sigma Aldrich. Potassium tetrachloropalladate(II) was prepared by the reaction of palladium chloride with a slight excess of potassium chloride. The complexes [Pd(bipy)Cl2] and [Pd(phen)Cl2], were obtained by adding 1 mmol of the respective ligand to 0.326 g (1 mmol) of K2[PdCl4] suspended/dissolved in 40 mL of wet methanol under reflux for about 1 h. The precipitated crystalline powders were recovered by filtration and dried under vacuum for 2 h. 0.25 mmol of these complexes (83 and 89 mg, respectively) were then suspended again in a water/methanol mixture, whereupon 0.5 mmol of the respective thiourea (1-5) was added under reflux. After 1 h, clear yellow to orange solutions were obtained. These solutions were filtrated and the filtrates were kept for 3-5 days at room temperature for crystallization. As a result yellow-red crystals were obtained. The experimental yield of the products, based on Pd, was more than 50%. All the solvents, of analytical grade, were dried and deoxygenated before being used. Elemental analyses were performed at the Microanalytical Laboratory of Redox snc (Milano). Characterization details are extensively quoted in the supplementary material.

Reference£º
Article; Rotondo, Archimede; Barresi, Salvatore; Cusumano, Matteo; Rotondo, Enrico; Polyhedron; vol. 45; 1; (2012); p. 23 – 29;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

The origin of a common compound about 52522-40-4

52522-40-4, General procedure: 0.1127g (0.4871mmol) of Me-TtBQ, 0.1755g (1.218mmol) of dmfu and 0.2101g (0.2030mmol) of [Pd2(DBA)3¡¤CHCl3] were dissolved under inert atmosphere (Ar) in 30ml of anhydrous acetone. The mixture was stirred for 60min and eventually treated with active charcoal for 5/10min and filtered on Celite filter. The resulting yellow solution was dried under vacuum and the residual treated with diethyl ether, filtered off, washed with diethyl ether in excess and dried under vacuum. 0.1452g (yield 75%) of the title compound was obtained as pale yellow microcrystals.

Reference£º
Article; Canovese, Luciano; Visentin, Fabiano; Biz, Chiara; Scattolin, Thomas; Santo, Claudio; Bertolasi, Valerio; Polyhedron; vol. 102; (2015); p. 94 – 102;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

Some scientific research about (2,2¡ä-Bipyridine)dichloropalladium(II)

14871-92-2 A common heterocyclic compound, 14871-92-2,(2,2¡ä-Bipyridine)dichloropalladium(II), its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route.

General procedure: [Pd(bpy)Cl2] (0.20 g, 0.60 mmol) was suspended in water (25 mL). Silver nitrate (0.20 g, 1.19 mmol) in water (5 mL) was added and the reaction mixture was stirred for 6 h at 60 C and then at room temperature, always in absence of light. The resulting solution was centrifuged and filtered to remove AgCl. A few drops of water, glycolic acid (0.05 g, 0.66 mmol) and 1 M NaOH (1.20 mL) were added to the filtrate. The resulting solution was stirred for 5 days and concentrated at 60 C to 5 mL on a rotary evaporator. The mixture was cooled to room temperature and the yellow powder was filtered off and dissolved from water and again concentrated to 5 mL. Yellow single crystals suitable for X-ray diffraction were obtained from the resulting solution by slow evaporation at room temperature.

Some scientific research about 52522-40-4

52522-40-4, General procedure: To 64.3 mg (0.278 mmol) of TTbQ-Me dissolved in anhydrous acetone (20 ml) in a two necked flask, 30 mg (0.278 mmol) of p-benzoquinone and 120 mg (0.116 mmol) of Pd2DBA3CHCl3 were added in sequence under inert atmosphere (Ar). The resulting mixture was stirred in the dark for 30 min, filtered on a celite filter and evaporated under vacuum to a small volume. Addition of Et2O induces the precipitation of the complex which was filtered off and dried in a desiccator for 5 h. 82.2 mg of the title compound as a red solid were obtained (yield 80percent).

Reference£º
Article; Canovese, Luciano; Visentin, Fabiano; Santo, Claudio; Bertolasi, Valerio; Journal of Organometallic Chemistry; vol. 749; (2014); p. 379 – 386;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

The important role of 14871-92-2

With the complex challenges of chemical substances, we look forward to future research findings about (2,2¡ä-Bipyridine)dichloropalladium(II)

Name is (2,2¡ä-Bipyridine)dichloropalladium(II), as a common heterocyclic compound, it belongs to catalyst-palladium compound, and cas is 14871-92-2, its synthesis route is as follows.,14871-92-2

General procedure: To a stirred suspension of [Pd(bpy)Cl2] (0.03 g, 0.1 mmol) or[Pd(phen)Cl2] (0.04 g, 0.1 mmol) in MeOH (10 mL) a solution ofHhmbt (0.023 g, 0.1 mmol) in MeOH containing KOH (0.006 g,0.1 mmol; 10 mL) was added drop by drop with stirring. The reactionmixture was warmed for 48 h, upon which a yellow-orangeprecipitate was filtered off, washed with MeOH, Et2O and driedin vacuo.For[Pd(bpy)(hmbt)]Cl2H2O: Yield: 0.07 g (51%). ElementalAnal.: Calcd. C, 49.5; H, 4.3; N, 12.6; Pd, 19.1 (C23H24N5O3Pd);Found: C, 49.7; H, 4.2; N, 12.7; Pd, 19.1%. Conductivity data(103 M in DMF): KM = 84.0 ohm1. IR (cm1): m(CN), 1621;m(CO), 1251; m(N-N), 1141; m(Pd-O), 500; m(Pd-N), 459. Raman(cm1): m(CN), 1602; m(CO), 1251; m(N-N), 1141; m(Pd-O), 501;m(Pd-N), 460. 1H NMR (ppm): 8.00 (H(3), d, J = 6 Hz, 1H); 7.75(H(6), S, 1H); 7.86 (H(7), d, J = 5.4 Hz, 1H); 7.73 (H(8), t, J = 5 Hz,1H); 7.69 (H(9), t, J = 5 Hz, 1H); 7.22 (H(10), d, J = 5.2 Hz, 1H);2.50 (CH3, S, 3H). MS (m/z): 486.4 (Calcd. 486.4), 368.2 (Calcd.368.4), 292.4 (Calcd. 292.4), 262.4 (Calcd. 262.4), 156.3 (Calcd.156.0).For[Pd(phen)(hmbt)]ClH2O: Yield: 0.08 g (54%). ElementalAnal.: Calcd. C, 53.2; H, 3.9; N, 12.4; Pd, 18.7 (C25H22N5O2Pd);Found: C, 53.3; H, 4.0; N, 12.3; Pd, 18.6%. Conductivity data(103 M in DMF): KM = 81.0 ohm1. IR (cm1): m(CN), 1600;m(CO), 1252; m(N-N), 1138; m(Pd-O), 564; m(Pd-N), 495. Raman(cm1): m(CN), 1604; m(CO), 1252; m(N-N), 1139; m(Pd-O), 565;m(Pd-N), 495. 1H NMR (ppm): 7.96 (H(3), d, J = 5.1 Hz, 1H); 7.30(H(6), S, 1H); 7.60 (H(7), d, J = 4.5 Hz, 1H); 7.77 (H(8), t,J = 4.2 Hz, 1H); 7.73 (H(9), t, J = 4.5 Hz, 1H); 7.22 (H(10), d,J = 4.2 Hz, 1H); 2.50 (CH3, S, 3H). MS (m/z): 510.4 (Calcd. 510.4),286.4 (Calcd. 286.4), 180.6 (Calcd. 180.0).

With the complex challenges of chemical substances, we look forward to future research findings about (2,2¡ä-Bipyridine)dichloropalladium(II)

Reference£º
Article; El-Asmy, Hala A.; Butler, Ian S.; Mouhri, Zhor S.; Jean-Claude, Bertrand J.; Emmam, Mohamed S.; Mostafa, Sahar I.; Journal of Molecular Structure; vol. 1059; 1; (2014); p. 193 – 201;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method