Downstream synthetic route of 14871-92-2

The synthetic route of 14871-92-2 has been constantly updated, and we look forward to future research findings.

14871-92-2, (2,2¡ä-Bipyridine)dichloropalladium(II) is a catalyst-palladium compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated

General procedure: Palladium(II) chloride (PdCl2), 2,2?-bipyridine (bipy), 1,10-phenanthroline (phen), thiourea (TU, 1), N-methylthiourea (meTU, 2), N-buthylthiourea (buTU, 3), N,N?-diethylthiourea (dietTU, 4) and N,N?-dibuthylthiourea (dibuTU, 5) were purchased as pure reagents at AG, from Sigma Aldrich. Potassium tetrachloropalladate(II) was prepared by the reaction of palladium chloride with a slight excess of potassium chloride. The complexes [Pd(bipy)Cl2] and [Pd(phen)Cl2], were obtained by adding 1 mmol of the respective ligand to 0.326 g (1 mmol) of K2[PdCl4] suspended/dissolved in 40 mL of wet methanol under reflux for about 1 h. The precipitated crystalline powders were recovered by filtration and dried under vacuum for 2 h. 0.25 mmol of these complexes (83 and 89 mg, respectively) were then suspended again in a water/methanol mixture, whereupon 0.5 mmol of the respective thiourea (1-5) was added under reflux. After 1 h, clear yellow to orange solutions were obtained. These solutions were filtrated and the filtrates were kept for 3-5 days at room temperature for crystallization. As a result yellow-red crystals were obtained. The experimental yield of the products, based on Pd, was more than 50%. All the solvents, of analytical grade, were dried and deoxygenated before being used. Elemental analyses were performed at the Microanalytical Laboratory of Redox snc (Milano). Characterization details are extensively quoted in the supplementary material.

The synthetic route of 14871-92-2 has been constantly updated, and we look forward to future research findings.

Reference£º
Article; Rotondo, Archimede; Barresi, Salvatore; Cusumano, Matteo; Rotondo, Enrico; Polyhedron; vol. 45; 1; (2012); p. 23 – 29;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

Some tips on 14871-92-2

As the paragraph descriping shows that 14871-92-2 is playing an increasingly important role.

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.14871-92-2,(2,2¡ä-Bipyridine)dichloropalladium(II),as a common compound, the synthetic route is as follows.

General procedure: Solid [Pd(L)Cl2] (L = bpy, phen) (0.2 mmol) was added to methanolic solution H2mesc (0.039 g, 0.2 mmol) containing KOH (0.0224 g, 0.4 mmol;; 15 mL). The mixture was stirred for 24 h. The yellow precipitate was filtered off, washed with methanol and air-dried. For [Pd(bpy)(mesc)]: Anal. Calc. For C20H15N2O4.5Pd: C, 52.0; H, 3.3; N, 6.1; Pd, 23.1%, Found: C, 52.1, H, 3.2; N, 6.0; Pd, 23.0%. Conductivity data (10-3 M in DMSO): LambdaM = 2.0 Ohm-1 cm2 mol-1. IR (cm-1); nu(C=O) 1664; nu(C-C) 1486; nu(C-O) 1254; nu(Pd-O) 521; nu(Pd-N) 427. 1H NMR (d6-DMSO/TMS, ppm), delta: CH3, 3.36; H(3), 6.66; H(8), 5.90; H(5), 6.50. ESI-MS: m/z: 905 (Calcd 904.8) [Pd(bpy)(mesc)]2+, 453 (Calcd 452.4) [Pd(bpy)(mesc)]+.

As the paragraph descriping shows that 14871-92-2 is playing an increasingly important role.

Reference£º
Article; Butler, Ian S.; Gilson, Denis F.R.; Jean-Claude, Bertrand J.; Mostafa, Sahar I.; Inorganica Chimica Acta; vol. 423; PB; (2014); p. 132 – 143;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

Simple exploration of 14871-92-2

As the paragraph descriping shows that 14871-92-2 is playing an increasingly important role.

14871-92-2, (2,2¡ä-Bipyridine)dichloropalladium(II) is a catalyst-palladium compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated

To a yellow suspension containing 0.30 g (0.90 mmol) of [Pd(bpy)Cl2] in water (20 mL) wereadded a solution containing 0.06 g (0.46 mmol) of HaptHCl in water (10 mL) and an aqueoussolution of NaOH (0.3 M, 10 mL). When the mixture was stirred at 50 C for 3 h, the suspensionturned to a yellow solution. After filtration, a saturated aqueous solution of NaNO3 (10 mL) wasadded to the yellow filtrate, followed by storing in a refrigerator for 1 week. The resulting yellowcrystals of [3](NO3)2 suitable for X-ray analysis were collected by filtration. Yield: 0.19 g (55%).

As the paragraph descriping shows that 14871-92-2 is playing an increasingly important role.

Reference£º
Article; Kouno, Masahiro; Miyashita, Yoshitaro; Yoshinari, Nobuto; Konno, Takumi; Chemistry Letters; vol. 44; 11; (2015); p. 1512 – 1514;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

Downstream synthetic route of 14871-92-2

The synthetic route of 14871-92-2 has been constantly updated, and we look forward to future research findings.

14871-92-2, (2,2¡ä-Bipyridine)dichloropalladium(II) is a catalyst-palladium compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated

To a yellow suspension containing 0.20 g (0.60 mmol) of [Pd(bpy)Cl2] in water (20 mL)was added 0.08 g (0.60 mmol) of HaptHCl. After the mixture was stirred at 50 C for 7 h, theresulting yellow solution was filtered. To the yellow filtrate was added an aqueous solution ofNaClO4 (2 M, 10 mL), followed by standing at room temperature for 1 d. The resulting yellowcrystals of [1](ClO4)4 suitable for X-ray analysis were collected by filtration. Yield: 0.32 g (87%).

The synthetic route of 14871-92-2 has been constantly updated, and we look forward to future research findings.

Reference£º
Article; Kouno, Masahiro; Miyashita, Yoshitaro; Yoshinari, Nobuto; Konno, Takumi; Chemistry Letters; vol. 44; 11; (2015); p. 1512 – 1514;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

Brief introduction of 14871-92-2

14871-92-2 (2,2¡ä-Bipyridine)dichloropalladium(II) 6096670, acatalyst-palladium compound, is more and more widely used in various.

14871-92-2, (2,2¡ä-Bipyridine)dichloropalladium(II) is a catalyst-palladium compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated

General procedure: Palladium(II) chloride (PdCl2), 2,2?-bipyridine (bipy), 1,10-phenanthroline (phen), thiourea (TU, 1), N-methylthiourea (meTU, 2), N-buthylthiourea (buTU, 3), N,N?-diethylthiourea (dietTU, 4) and N,N?-dibuthylthiourea (dibuTU, 5) were purchased as pure reagents at AG, from Sigma Aldrich. Potassium tetrachloropalladate(II) was prepared by the reaction of palladium chloride with a slight excess of potassium chloride. The complexes [Pd(bipy)Cl2] and [Pd(phen)Cl2], were obtained by adding 1 mmol of the respective ligand to 0.326 g (1 mmol) of K2[PdCl4] suspended/dissolved in 40 mL of wet methanol under reflux for about 1 h. The precipitated crystalline powders were recovered by filtration and dried under vacuum for 2 h. 0.25 mmol of these complexes (83 and 89 mg, respectively) were then suspended again in a water/methanol mixture, whereupon 0.5 mmol of the respective thiourea (1-5) was added under reflux. After 1 h, clear yellow to orange solutions were obtained. These solutions were filtrated and the filtrates were kept for 3-5 days at room temperature for crystallization. As a result yellow-red crystals were obtained. The experimental yield of the products, based on Pd, was more than 50%. All the solvents, of analytical grade, were dried and deoxygenated before being used. Elemental analyses were performed at the Microanalytical Laboratory of Redox snc (Milano). Characterization details are extensively quoted in the supplementary material.

14871-92-2 (2,2¡ä-Bipyridine)dichloropalladium(II) 6096670, acatalyst-palladium compound, is more and more widely used in various.

Reference£º
Article; Rotondo, Archimede; Barresi, Salvatore; Cusumano, Matteo; Rotondo, Enrico; Polyhedron; vol. 45; 1; (2012); p. 23 – 29;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

Analyzing the synthesis route of 14871-92-2

14871-92-2 (2,2¡ä-Bipyridine)dichloropalladium(II) 6096670, acatalyst-palladium compound, is more and more widely used in various.

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.14871-92-2,(2,2¡ä-Bipyridine)dichloropalladium(II),as a common compound, the synthetic route is as follows.

To a vigorously stirred solution of BzpheH2 (32.32 mg,0.12 mmol) in 8 mL CH3OH/H2O (V:V D 1:1), [Pd(bipy)Cl2] (20 mg, 0.06 mmol) was added. The mixture was heatedto 50C and adjusted to pH D 8-9 by NaOH solution, andthen stirred for 2 h. The solution was concentrated to about80% of the original volume. The complex I-a was separatedfrom the solution after a few days. Yellow crystalline, yield: 68%. IR (KBr, cm1): n(Amide&)1551, n(OCO)a 1632, n(OCO)a1383, n(Pd-N) 566, n(Pd-O) 465. 1H NMR (600 MHz, d6-DMSO) d (ppm): 3.08 (dd, J D 13.1, 4.5 Hz, 1H, CH2-H),3.29 (dd, J D 13.1, 4.5 Hz, 1H, CH2-H), 5.08-5.05 (m, 1H,CH), 6.65 (t, J D 7.5 Hz, 1H, Ar-H), 6.73 (t, J D 7.5 Hz, 2H,Ar-H), 7.09 (d, J D 3.0 Hz, 3H, Ar-H), 7.13 (d, J D 5.4 Hz,1H, Ar-H), 7.23 (d, J D 7.2 Hz, 2H, Ar-H), 7.28 (d, J D5.4 Hz, 1H, Ar-H), 7.78-7.75 (m, 1H, Ar-H), 8.02 (t, J D7.8 Hz, 1H, Ar-H), 8.26 (d, J D 7.8 Hz, 1H, Ar-H), 8.30 (t, JD 6.9 Hz, 4H, Ar-H), 8.42 (d, J D 7.8 Hz, 1H, Ar-H). ESIMS:568.03 [MCK]C. Anal. Calcd. for [Pd(bipy)(Bzphe-N,O)] (C26H21N3O3Pd, 529.06): C, 58.93; H, 3.99; N, 7.93.Found: C, 58.84; H, 4.04; N, 7.84.

14871-92-2 (2,2¡ä-Bipyridine)dichloropalladium(II) 6096670, acatalyst-palladium compound, is more and more widely used in various.

Reference£º
Article; Wang, Li-Wei; Liu, Si-Yuan; Wang, Jin-Jie; Peng, Wen; Li, Sheng-Hui; Zhou, Guo-Qiang; Qin, Xin-Ying; Wang, Shu-Xiang; Zhang, Jin-Chao; Synthesis and Reactivity in Inorganic, Metal-Organic, and Nano-Metal Chemistry; vol. 45; 7; (2015); p. 1049 – 1056;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

Simple exploration of 14871-92-2

As the paragraph descriping shows that 14871-92-2 is playing an increasingly important role.

14871-92-2, (2,2¡ä-Bipyridine)dichloropalladium(II) is a catalyst-palladium compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated

General procedure: Silver tetrafluoroborate (AgBF4) (0.6 mmol) was dissolvedin methanol (7 mL); (2,2?-bipyridine) dichloropalladium(II)(Pd(Bpy)Cl2) (0.3 mmol) was dissolved in DMSO (1 mL),and then, the solutions were stirred together at ambient temperature0.5 h. Following gravity filtration, solid 3-hydroxyflavonederivative (0.3 mmol) and triethylamine (0.7 mL)were added to the filtrate. The reaction mixture was stirredfor 0.5 h (2 h for the Fla-OMe). The corresponding bipyridinepalladium flavonolato salt was then recovered usingvacuum filtration and recrystallized in CH3OH/CH3CN solvent;remaining solvent was removed in a vacuum desiccator overnight.

As the paragraph descriping shows that 14871-92-2 is playing an increasingly important role.

Reference£º
Article; Han, Xiaozhen; Whitfield, Sarah; Cotten, Jacob; Transition Metal Chemistry; (2019);,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

Brief introduction of 14871-92-2

14871-92-2 (2,2¡ä-Bipyridine)dichloropalladium(II) 6096670, acatalyst-palladium compound, is more and more widely used in various.

14871-92-2, (2,2¡ä-Bipyridine)dichloropalladium(II) is a catalyst-palladium compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated

General procedure: Silver tetrafluoroborate (AgBF4) (0.6 mmol) was dissolvedin methanol (7 mL); (2,2?-bipyridine) dichloropalladium(II)(Pd(Bpy)Cl2) (0.3 mmol) was dissolved in DMSO (1 mL),and then, the solutions were stirred together at ambient temperature0.5 h. Following gravity filtration, solid 3-hydroxyflavonederivative (0.3 mmol) and triethylamine (0.7 mL)were added to the filtrate. The reaction mixture was stirredfor 0.5 h (2 h for the Fla-OMe). The corresponding bipyridinepalladium flavonolato salt was then recovered usingvacuum filtration and recrystallized in CH3OH/CH3CN solvent;remaining solvent was removed in a vacuum desiccator overnight.

14871-92-2 (2,2¡ä-Bipyridine)dichloropalladium(II) 6096670, acatalyst-palladium compound, is more and more widely used in various.

Reference£º
Article; Han, Xiaozhen; Whitfield, Sarah; Cotten, Jacob; Transition Metal Chemistry; (2019);,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

Brief introduction of 14871-92-2

14871-92-2 (2,2¡ä-Bipyridine)dichloropalladium(II) 6096670, acatalyst-palladium compound, is more and more widely used in various.

14871-92-2, (2,2¡ä-Bipyridine)dichloropalladium(II) is a catalyst-palladium compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated

Mefenamic acid (0.40 mmol) was dissolved in methanol (15 mL) followed by the addition of KOH (0.40 mmol). After 60 min of stirring, the resulting solution was slowly added to an aqueous solution of [PdCl2(bipy)] (0.20 mmol). After 40 min of constant stirring, the yellow solid obtained was collected by filtration, washed with ethanol and dried in a desiccator with P4O10. The yield was 63%. Anal. Calc. for [Pd(C15H14NO2)2(bipy)] (%): C 64.6; H 4.88;N 7.54. Found: C 63.3; H 4.74; N 7.62. The complex is soluble inchloroform and insoluble in water and DMSO. As already observed for the Pd-tra complex, no single crystals were obtained to perform an X ray structural characterization. The [PdCl2(bipy)] complexused as a precursor in the synthesis of Pd-mef was synthesized as described in the literature [21].

14871-92-2 (2,2¡ä-Bipyridine)dichloropalladium(II) 6096670, acatalyst-palladium compound, is more and more widely used in various.

Reference£º
Article; Carvalho, Marcos A.; Arruda, Eduardo G.R.; Profirio, Daniel M.; Gomes, Alexandre F.; Gozzo, Fabio C.; Formiga, Andre L.B.; Corbi, Pedro P.; Journal of Molecular Structure; vol. 1100; (2015); p. 6 – 13;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

Some tips on 14871-92-2

As the paragraph descriping shows that 14871-92-2 is playing an increasingly important role.

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.14871-92-2,(2,2¡ä-Bipyridine)dichloropalladium(II),as a common compound, the synthetic route is as follows.

General procedure: To a stirred suspension of [Pd(bpy)Cl2] (0.03 g, 0.1 mmol) or[Pd(phen)Cl2] (0.04 g, 0.1 mmol) in MeOH (10 mL) a solution ofHhmbt (0.023 g, 0.1 mmol) in MeOH containing KOH (0.006 g,0.1 mmol; 10 mL) was added drop by drop with stirring. The reactionmixture was warmed for 48 h, upon which a yellow-orangeprecipitate was filtered off, washed with MeOH, Et2O and driedin vacuo.For[Pd(bpy)(hmbt)]Cl2H2O: Yield: 0.07 g (51%). ElementalAnal.: Calcd. C, 49.5; H, 4.3; N, 12.6; Pd, 19.1 (C23H24N5O3Pd);Found: C, 49.7; H, 4.2; N, 12.7; Pd, 19.1%. Conductivity data(103 M in DMF): KM = 84.0 ohm1. IR (cm1): m(CN), 1621;m(CO), 1251; m(N-N), 1141; m(Pd-O), 500; m(Pd-N), 459. Raman(cm1): m(CN), 1602; m(CO), 1251; m(N-N), 1141; m(Pd-O), 501;m(Pd-N), 460. 1H NMR (ppm): 8.00 (H(3), d, J = 6 Hz, 1H); 7.75(H(6), S, 1H); 7.86 (H(7), d, J = 5.4 Hz, 1H); 7.73 (H(8), t, J = 5 Hz,1H); 7.69 (H(9), t, J = 5 Hz, 1H); 7.22 (H(10), d, J = 5.2 Hz, 1H);2.50 (CH3, S, 3H). MS (m/z): 486.4 (Calcd. 486.4), 368.2 (Calcd.368.4), 292.4 (Calcd. 292.4), 262.4 (Calcd. 262.4), 156.3 (Calcd.156.0).For[Pd(phen)(hmbt)]ClH2O: Yield: 0.08 g (54%). ElementalAnal.: Calcd. C, 53.2; H, 3.9; N, 12.4; Pd, 18.7 (C25H22N5O2Pd);Found: C, 53.3; H, 4.0; N, 12.3; Pd, 18.6%. Conductivity data(103 M in DMF): KM = 81.0 ohm1. IR (cm1): m(CN), 1600;m(CO), 1252; m(N-N), 1138; m(Pd-O), 564; m(Pd-N), 495. Raman(cm1): m(CN), 1604; m(CO), 1252; m(N-N), 1139; m(Pd-O), 565;m(Pd-N), 495. 1H NMR (ppm): 7.96 (H(3), d, J = 5.1 Hz, 1H); 7.30(H(6), S, 1H); 7.60 (H(7), d, J = 4.5 Hz, 1H); 7.77 (H(8), t,J = 4.2 Hz, 1H); 7.73 (H(9), t, J = 4.5 Hz, 1H); 7.22 (H(10), d,J = 4.2 Hz, 1H); 2.50 (CH3, S, 3H). MS (m/z): 510.4 (Calcd. 510.4),286.4 (Calcd. 286.4), 180.6 (Calcd. 180.0).

As the paragraph descriping shows that 14871-92-2 is playing an increasingly important role.

Reference£º
Article; El-Asmy, Hala A.; Butler, Ian S.; Mouhri, Zhor S.; Jean-Claude, Bertrand J.; Emmam, Mohamed S.; Mostafa, Sahar I.; Journal of Molecular Structure; vol. 1059; 1; (2014); p. 193 – 201;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method