Tag: M.W:300-400

14871-92-2, In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact. (2,2¡ä-Bipyridine)dichloropalladium(II), cas is 14871-92-2,the catalyst-palladium compound, it is a common compound, a new synthetic route is introduced below.

General procedure: Silver tetrafluoroborate (AgBF4) (0.6 mmol) was dissolvedin methanol (7 mL); (2,2?-bipyridine) dichloropalladium(II)(Pd(Bpy)Cl2) (0.3 mmol) was dissolved in DMSO (1 mL),and then, the solutions were stirred together at ambient temperature0.5 h. Following gravity filtration, solid 3-hydroxyflavonederivative (0.3 mmol) and triethylamine (0.7 mL)were added to the filtrate. The reaction mixture was stirredfor 0.5 h (2 h for the Fla-OMe). The corresponding bipyridinepalladium flavonolato salt was then recovered usingvacuum filtration and recrystallized in CH3OH/CH3CN solvent;remaining solvent was removed in a vacuum desiccator overnight.

Chemical properties determine the actual use. Each compound has specific chemical properties and uses. We look forward to more synthetic routes in the future to expand reaction routes of (2,2¡ä-Bipyridine)dichloropalladium(II), 14871-92-2

Reference£º
Article; Han, Xiaozhen; Whitfield, Sarah; Cotten, Jacob; Transition Metal Chemistry; (2019);,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

As a common heterocyclic compound, it belongs to catalyst-palladium compound, name is Potassium chloropalladite, and cas is 10025-98-6, its synthesis route is as follows.

General procedure: The complexes [Pd(bipy)Cl2] and [Pd(phen)Cl2], were obtained by adding 1 mmol of the respective ligand to 0.326 g (1 mmol) of K2[PdCl4] suspended/dissolved in 40 mL of wet methanol under reflux for about 1 h. The precipitated crystalline powders were recovered by filtration and dried under vacuum for 2 h.

10025-98-6, In the field of chemistry, the synthetic routes of compounds are constantly being developed and updated. I will also mention this compound in other articles.,10025-98-6 ,Potassium chloropalladite, other downstream synthetic routes, hurry up and to see

Reference£º
Article; Rotondo, Archimede; Barresi, Salvatore; Cusumano, Matteo; Rotondo, Enrico; Polyhedron; vol. 45; 1; (2012); p. 23 – 29;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

14871-92-2, In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact. (2,2¡ä-Bipyridine)dichloropalladium(II), cas is 14871-92-2,the catalyst-palladium compound, it is a common compound, a new synthetic route is introduced below.

The new bimetallic dinuclear complex, [{PdCl(bipy)}{l-(NH2(CH2)6H2N)}{PtCl(bipy)}]Cl(ClO4), was synthesized by modificationof the procedure reported in the literature [25]. The complex[PtCl2(bipy)] (100.0 mg, 0.236 mmol) was dissolved in DMF(10 cm3) and a solution of AgClO4 (49.1 mg, 0.236 mmol) in DMF(5 cm3) was added. The mixture was stirred overnight in the dark,at room temperature. The precipitate AgCl was removed by filtrationand the resulting pale yellow solution of [PtCl(bipy)(DMF)]ClO4 was kept in a refrigerator to cool down. A suspension of[PdCl2(bipy)] complex (73.5 mg, 0.220 mmol) in 10 cm3 of DMFwas heated with stirring at 303-313 K for about 30 min. After that,the solution of 1,6-diaminohexane (25.5 mg, 0.220 mmol) in 5 cm3DMF was added dropwise. The mixture was stirred at room temperaturefor 5 h in the dark. The filtrate [PtCl(bipy)(DMF)]ClO4was added to the resulting mixture. The clear yellow solutionwas stirred for 3 h at 323 K and then for 24 h at room temperature.The solution was then evaporated and the residue washed withether. A light yellow powder was obtained and left to dry in theair. Yield (63.8 mg, 62%). Anal. Calc. for PtPdCl4O4N6C26H32(FW = 935.88): C, 33.37; H, 3.45; N, 8.98. Found: C, 33.07; H,3.80; N, 8.73%. 1H NMR characterization (D2O, 200 MHz). 1H NMR(d, ppm): 1.35-1.50 (m, CH2 C3, C4), 1.60-1.80 (m, CH2 C2, C5),2.95-3.06 (m, CH2 C1, C6), 7.30-7.42 (d, CH H5/H50(1)), 7.45-7.60 (d, CH H5/H50(2)), 7.65-7.84 (m, CH H4/H40(1)), 8.05-8.15(m CH H4/H40(2)), 8.17-8.28 m, CH H3/H30(1)), 8.32-8.40 (m, CHH3/H30(2)), 8.42-8.48 (d CH H6/H60(1)), 8.50-8.58 (d CH H6/H60(2)). IR (KBr, 4000-300 cm1): 3438 (N-H stretch); 2853, 2927(CH2 stretch); 1610 (CN stretch); 1089 (perchlorate counterion); 765, 812 (N-H wagging) (Fig. S1).

Chemical properties determine the actual use. Each compound has specific chemical properties and uses. We look forward to more synthetic routes in the future to expand reaction routes of (2,2¡ä-Bipyridine)dichloropalladium(II), 14871-92-2

Reference£º
Article; Jovanovi?, Sne?ana; Petrovi?, Biljana; Petkovi?, Marijana; Bugar?i?, ?ivadin D.; Polyhedron; vol. 101; (2015); p. 206 – 214;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

14871-92-2, In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact. (2,2¡ä-Bipyridine)dichloropalladium(II), cas is 14871-92-2,the catalyst-palladium compound, it is a common compound, a new synthetic route is introduced below.

General procedure: Palladium(II) chloride (PdCl2), 2,2?-bipyridine (bipy), 1,10-phenanthroline (phen), thiourea (TU, 1), N-methylthiourea (meTU, 2), N-buthylthiourea (buTU, 3), N,N?-diethylthiourea (dietTU, 4) and N,N?-dibuthylthiourea (dibuTU, 5) were purchased as pure reagents at AG, from Sigma Aldrich. Potassium tetrachloropalladate(II) was prepared by the reaction of palladium chloride with a slight excess of potassium chloride. The complexes [Pd(bipy)Cl2] and [Pd(phen)Cl2], were obtained by adding 1 mmol of the respective ligand to 0.326 g (1 mmol) of K2[PdCl4] suspended/dissolved in 40 mL of wet methanol under reflux for about 1 h. The precipitated crystalline powders were recovered by filtration and dried under vacuum for 2 h. 0.25 mmol of these complexes (83 and 89 mg, respectively) were then suspended again in a water/methanol mixture, whereupon 0.5 mmol of the respective thiourea (1-5) was added under reflux. After 1 h, clear yellow to orange solutions were obtained. These solutions were filtrated and the filtrates were kept for 3-5 days at room temperature for crystallization. As a result yellow-red crystals were obtained. The experimental yield of the products, based on Pd, was more than 50%. All the solvents, of analytical grade, were dried and deoxygenated before being used. Elemental analyses were performed at the Microanalytical Laboratory of Redox snc (Milano). Characterization details are extensively quoted in the supplementary material.

The chemical industry reduces the impact on the environment during synthesis,14871-92-2,(2,2¡ä-Bipyridine)dichloropalladium(II),I believe this compound will play a more active role in future production and life.

Reference£º
Article; Rotondo, Archimede; Barresi, Salvatore; Cusumano, Matteo; Rotondo, Enrico; Polyhedron; vol. 45; 1; (2012); p. 23 – 29;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

As a common heterocyclic compound, it belongs to catalyst-palladium compound, name is (2,2¡ä-Bipyridine)dichloropalladium(II), and cas is 14871-92-2, its synthesis route is as follows.

(bpy)PdCl2 (167 mg, 0.5 mmol) and AgNO3 (170 mg, 1.0 mmol) was mixed in CH3NO2 (40 mL). The mixture was stirred at 60 C for 24 hrs, and the white AgCl precipitate was filtered by a short pad of celite. The filtrate was sampled for ESI-HRMS, and cationic C20H18N4O2Pd22+ (m/z: 279.9743) was observed. Then the filtrate was concentrated and recrystallized to give 25 mg light yellow needle-like solid. Yield 9.0%.

14871-92-2, In the field of chemistry, the synthetic routes of compounds are constantly being developed and updated. I will also mention this compound in other articles.,14871-92-2 ,(2,2¡ä-Bipyridine)dichloropalladium(II), other downstream synthetic routes, hurry up and to see

Reference£º
Article; Yang, Zhenyu; Ni, Yuxin; Liu, Rui; Song, Kaixuan; Lin, Shaohui; Pan, Qinmin; Tetrahedron Letters; vol. 58; 21; (2017); p. 2034 – 2037;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

14871-92-2, In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact. (2,2¡ä-Bipyridine)dichloropalladium(II), cas is 14871-92-2,the catalyst-palladium compound, it is a common compound, a new synthetic route is introduced below.

[Pd(bpy)Cl2] (.67 g, 2 mmol) was suspended in 200 mlacetone-water (3:1 v/v) and AgNO3 (.68 g, 4 mmol) wasadded with constant stirring. This mixture was heated at328 K with stirring in the dark for 6 h followed by stirringfor 16 h at room temperature. The AgCl precipitatewas removed by filtration using Whatman 42 filter paper.The clear yellow filtrate was mixed with mu-paraxylidinebisdithiocarbamatedisodium salt (.33 g, 1 mmol).The reaction mixture was subsequently stirred for 5 h at318 K and then filtered. The clear solution was concentratedto 5 ml at 318 K. The resulting yellow precipitatewas filtered and washed with small amounts of acetoneand resolved in 300 ml doubly distilled water at 318 K.The solution was filtered to remove turbidity. The clearsolution was then concentrated to 5 ml and refrigeratedovernight. The yellow precipitate was filtered and washedwith small amounts of cold distilled water and acetoneand dried in an oven at 318 K. The synthesis of the complexcan be summarized by Figure 1. Yield: .572 g(65%), Decomposition ranges: 520-523 K. Anal. Calcd.for C30H26N6S4Cl2Pd2: C, 40.86; H, 2.95, N, 9.53%.Found: C, 40.85; H, 2.96, N, 9.55%. Molar conductance,LambdaM (H2O, Omega-1 mol-1 cm2): 243. FT-IR (KBr pellets,cm-1): 1541 upsilon (C-N); 1022 upsilon (C-S) and 1385 (NO3- ion).UV-Vis data (water, lambdamax/nm (logepsilon): 308 (3.43), 247 (3.79) and 188 (3.95). 1H NMR (500 MHz, DMSO-d6,ppm, d = doublet, t = triplet and m = multiple): 7.66 (m,1H, H-a), 8.23 (m, 2H, H-b), 8.48 (d, 2H, H-c), 7.79(t, 2H, H-5,5), 8.30 (t, 2H, H-4,4), 8.57 (d, 2H, H-3,3),8.88 (d, 2H, H-6,6) (Figure S1).

The chemical industry reduces the impact on the environment during synthesis,14871-92-2,(2,2¡ä-Bipyridine)dichloropalladium(II),I believe this compound will play a more active role in future production and life.

Reference£º
Letter; Saeidifar, Maryam; Sohrabi Jam, Zahra; Shahraki, Somayeh; Khanlarkhani, Ali; Javaheri, Masoumeh; Divsalar, Adeleh; Mansouri-Torshizi, Hassan; Akbar Saboury, Ali; Journal of Biomolecular Structure and Dynamics; vol. 35; 12; (2017); p. 2557 – 2564;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

It is a common heterocyclic compound, the catalyst-palladium compound, (2,2¡ä-Bipyridine)dichloropalladium(II), cas is 14871-92-2 its synthesis route is as follows.

Pd(2,2?-bpy)Cl2 (67 mg, 0.2 mmol) was stirred with AgNO3 (68 mg, 0.4 mmol) in water (10 mL) with light excluded at 40 C for 12 h. The suspension obtained was cooled to 0 C in ice bath for 30 min. Then AgCl was removed from the solution by filtration. 1 (52.8 mg, 0.2 mmol) was added to the clear filtrate and pH was measured and found to be 2.0. Then the mixture was stirred at 40 C for 2 h. The resulting light yellow solution was concentrated to a volume of 5 mL at 40 C on a rotary evaporator. Yellow cubes were obtained after one day. The yield was 85 mg (60%). 1H NMR (D2O, pD 2.0, 298 K, delta, ppm): 1?, 3.69 (12 H, s, CH3), 3.60 (4H, s, CH2), 7.93 (4H, s, H6); 2,2?-bpy, 7.23 (4H, dd, H5, 3JH-H = 6.0 Hz, 4JH-H = 3.0 Hz), 7.60 (4H, t, H5?, 3JH-H = 7.2 Hz), 7.79 (4H, dd, H6, 3JH-H = 6.0 Hz), 7.94-8.18 (20H, m, H3,H3?,H4,H4?,H6?).

14871-92-2, In the field of chemistry, the synthetic routes of compounds are constantly being developed and updated. I will also mention this compound in other articles.,14871-92-2 ,(2,2¡ä-Bipyridine)dichloropalladium(II), other downstream synthetic routes, hurry up and to see

Reference£º
Article; Khutia, Anupam; Shen, Wei-Zheng; Das, Neeladri; Sanz Miguel, Pablo J.; Lippert, Bernhard; Inorganica Chimica Acta; vol. 417; (2014); p. 274 – 286;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

It is a common heterocyclic compound, the catalyst-palladium compound, (2,2¡ä-Bipyridine)dichloropalladium(II), cas is 14871-92-2 its synthesis route is as follows.

General procedure: Palladium(II) chloride (PdCl2), 2,2?-bipyridine (bipy), 1,10-phenanthroline (phen), thiourea (TU, 1), N-methylthiourea (meTU, 2), N-buthylthiourea (buTU, 3), N,N?-diethylthiourea (dietTU, 4) and N,N?-dibuthylthiourea (dibuTU, 5) were purchased as pure reagents at AG, from Sigma Aldrich. Potassium tetrachloropalladate(II) was prepared by the reaction of palladium chloride with a slight excess of potassium chloride. The complexes [Pd(bipy)Cl2] and [Pd(phen)Cl2], were obtained by adding 1 mmol of the respective ligand to 0.326 g (1 mmol) of K2[PdCl4] suspended/dissolved in 40 mL of wet methanol under reflux for about 1 h. The precipitated crystalline powders were recovered by filtration and dried under vacuum for 2 h. 0.25 mmol of these complexes (83 and 89 mg, respectively) were then suspended again in a water/methanol mixture, whereupon 0.5 mmol of the respective thiourea (1-5) was added under reflux. After 1 h, clear yellow to orange solutions were obtained. These solutions were filtrated and the filtrates were kept for 3-5 days at room temperature for crystallization. As a result yellow-red crystals were obtained. The experimental yield of the products, based on Pd, was more than 50%. All the solvents, of analytical grade, were dried and deoxygenated before being used. Elemental analyses were performed at the Microanalytical Laboratory of Redox snc (Milano). Characterization details are extensively quoted in the supplementary material.

14871-92-2, In the field of chemistry, the synthetic routes of compounds are constantly being developed and updated. I will also mention this compound in other articles.,14871-92-2 ,(2,2¡ä-Bipyridine)dichloropalladium(II), other downstream synthetic routes, hurry up and to see

Reference£º
Article; Rotondo, Archimede; Barresi, Salvatore; Cusumano, Matteo; Rotondo, Enrico; Polyhedron; vol. 45; 1; (2012); p. 23 – 29;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

14871-92-2, In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact. (2,2¡ä-Bipyridine)dichloropalladium(II), cas is 14871-92-2,the catalyst-palladium compound, it is a common compound, a new synthetic route is introduced below.

First, 63.6 mg (0.2 mmol)Of compounds 111-5 and 32.2 mmol (0.6 mmol)Of methanol was added to a mixture of 30 ml of anhydrous methanol and tetrahydrofuran(Volume ratio of 1: 1)Argon protection,After stirring at room temperature for 1.5 h,Followed by the addition of 66.4 mg (0.2 mmol) of cis-dichloro-1,1′-bipyridyl palladium (II)Continue to argon protection,Stirring at 25 C for 14 h,After the reaction,The resulting solid was purified by column chromatography,Get the target product,Weight 93.8 mg, yield: 85%.

The chemical industry reduces the impact on the environment during synthesis,14871-92-2,(2,2¡ä-Bipyridine)dichloropalladium(II),I believe this compound will play a more active role in future production and life.

Reference£º
Patent; Changchun Institute of Applied Chemistry, Chinese Academy of Sciences; Wang, Zhiyuan; Liu, Bo; Qiao, Wenqiang; (34 pag.)CN103483391; (2016); B;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

14871-92-2, In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact. (2,2¡ä-Bipyridine)dichloropalladium(II), cas is 14871-92-2,the catalyst-palladium compound, it is a common compound, a new synthetic route is introduced below.

To a vigorously stirred solution of BzpheH2 (32.32 mg,0.12 mmol) in 8 mL CH3OH/H2O (V:V D 1:1), [Pd(bipy)Cl2] (20 mg, 0.06 mmol) was added. The mixture was heatedto 50C and adjusted to pH D 8-9 by NaOH solution, andthen stirred for 2 h. The solution was concentrated to about80% of the original volume. The complex I-a was separatedfrom the solution after a few days. Yellow crystalline, yield: 68%. IR (KBr, cm1): n(Amide&)1551, n(OCO)a 1632, n(OCO)a1383, n(Pd-N) 566, n(Pd-O) 465. 1H NMR (600 MHz, d6-DMSO) d (ppm): 3.08 (dd, J D 13.1, 4.5 Hz, 1H, CH2-H),3.29 (dd, J D 13.1, 4.5 Hz, 1H, CH2-H), 5.08-5.05 (m, 1H,CH), 6.65 (t, J D 7.5 Hz, 1H, Ar-H), 6.73 (t, J D 7.5 Hz, 2H,Ar-H), 7.09 (d, J D 3.0 Hz, 3H, Ar-H), 7.13 (d, J D 5.4 Hz,1H, Ar-H), 7.23 (d, J D 7.2 Hz, 2H, Ar-H), 7.28 (d, J D5.4 Hz, 1H, Ar-H), 7.78-7.75 (m, 1H, Ar-H), 8.02 (t, J D7.8 Hz, 1H, Ar-H), 8.26 (d, J D 7.8 Hz, 1H, Ar-H), 8.30 (t, JD 6.9 Hz, 4H, Ar-H), 8.42 (d, J D 7.8 Hz, 1H, Ar-H). ESIMS:568.03 [MCK]C. Anal. Calcd. for [Pd(bipy)(Bzphe-N,O)] (C26H21N3O3Pd, 529.06): C, 58.93; H, 3.99; N, 7.93.Found: C, 58.84; H, 4.04; N, 7.84.

Chemical properties determine the actual use. Each compound has specific chemical properties and uses. We look forward to more synthetic routes in the future to expand reaction routes of (2,2¡ä-Bipyridine)dichloropalladium(II), 14871-92-2

Reference£º
Article; Wang, Li-Wei; Liu, Si-Yuan; Wang, Jin-Jie; Peng, Wen; Li, Sheng-Hui; Zhou, Guo-Qiang; Qin, Xin-Ying; Wang, Shu-Xiang; Zhang, Jin-Chao; Synthesis and Reactivity in Inorganic, Metal-Organic, and Nano-Metal Chemistry; vol. 45; 7; (2015); p. 1049 – 1056;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method