Tag: M.W:300-400

14871-92-2 A common heterocyclic compound, 14871-92-2,(2,2¡ä-Bipyridine)dichloropalladium(II), its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route.

Pd(2,2?-bpy)Cl2 (67 mg, 0.2 mmol) was stirred with AgNO3 (68 mg, 0.4 mmol) in water (10 mL) with light excluded at 40 C for 12 h. The suspension obtained was cooled to 0 C in ice bath for 30 min. Then AgCl was removed from the solution by filtration. 1 (52.8 mg, 0.2 mmol) was added to the clear filtrate and pH was measured and found to be 2.0. Then the mixture was stirred at 40 C for 2 h. The resulting light yellow solution was concentrated to a volume of 5 mL at 40 C on a rotary evaporator. Yellow cubes were obtained after one day. The yield was 85 mg (60%). 1H NMR (D2O, pD 2.0, 298 K, delta, ppm): 1?, 3.69 (12 H, s, CH3), 3.60 (4H, s, CH2), 7.93 (4H, s, H6); 2,2?-bpy, 7.23 (4H, dd, H5, 3JH-H = 6.0 Hz, 4JH-H = 3.0 Hz), 7.60 (4H, t, H5?, 3JH-H = 7.2 Hz), 7.79 (4H, dd, H6, 3JH-H = 6.0 Hz), 7.94-8.18 (20H, m, H3,H3?,H4,H4?,H6?).

This compound has a wide range of applications. It is believed that with the continuous development of the source of the synthetic route,14871-92-2,(2,2¡ä-Bipyridine)dichloropalladium(II),its application will become more common.

Reference£º
Article; Khutia, Anupam; Shen, Wei-Zheng; Das, Neeladri; Sanz Miguel, Pablo J.; Lippert, Bernhard; Inorganica Chimica Acta; vol. 417; (2014); p. 274 – 286;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

A common heterocyclic compound, 14871-92-2,(2,2¡ä-Bipyridine)dichloropalladium(II), its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route. 14871-92-2

General procedure: Palladium(II) chloride (PdCl2), 2,2?-bipyridine (bipy), 1,10-phenanthroline (phen), thiourea (TU, 1), N-methylthiourea (meTU, 2), N-buthylthiourea (buTU, 3), N,N?-diethylthiourea (dietTU, 4) and N,N?-dibuthylthiourea (dibuTU, 5) were purchased as pure reagents at AG, from Sigma Aldrich. Potassium tetrachloropalladate(II) was prepared by the reaction of palladium chloride with a slight excess of potassium chloride. The complexes [Pd(bipy)Cl2] and [Pd(phen)Cl2], were obtained by adding 1 mmol of the respective ligand to 0.326 g (1 mmol) of K2[PdCl4] suspended/dissolved in 40 mL of wet methanol under reflux for about 1 h. The precipitated crystalline powders were recovered by filtration and dried under vacuum for 2 h. 0.25 mmol of these complexes (83 and 89 mg, respectively) were then suspended again in a water/methanol mixture, whereupon 0.5 mmol of the respective thiourea (1-5) was added under reflux. After 1 h, clear yellow to orange solutions were obtained. These solutions were filtrated and the filtrates were kept for 3-5 days at room temperature for crystallization. As a result yellow-red crystals were obtained. The experimental yield of the products, based on Pd, was more than 50%. All the solvents, of analytical grade, were dried and deoxygenated before being used. Elemental analyses were performed at the Microanalytical Laboratory of Redox snc (Milano). Characterization details are extensively quoted in the supplementary material., 14871-92-2

This compound has a wide range of applications. It is believed that with the continuous development of the source of the synthetic route,(2,2¡ä-Bipyridine)dichloropalladium(II),14871-92-2,its application will become more common.

Reference£º
Article; Rotondo, Archimede; Barresi, Salvatore; Cusumano, Matteo; Rotondo, Enrico; Polyhedron; vol. 45; 1; (2012); p. 23 – 29;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

14871-92-2 A common heterocyclic compound, 14871-92-2,(2,2¡ä-Bipyridine)dichloropalladium(II), its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route.

Pd(2,2?-bpy)Cl2 (67 mg, 0.2 mmol) was stirred with AgNO3 (68 mg, 0.4 mmol) in water (10 mL) with light excluded at 40 C for 12 h. The suspension obtained was cooled to 0 C in ice bath for 30 min. Then AgCl was removed from the solution by filtration. 1 (52.8 mg, 0.2 mmol) was added to the clear filtrate and pH was measured and found to be 2.0. Then the mixture was stirred at 40 C for 2 h. The resulting light yellow solution was concentrated to a volume of 5 mL at 40 C on a rotary evaporator. Yellow cubes were obtained after one day. The yield was 85 mg (60%). 1H NMR (D2O, pD 2.0, 298 K, delta, ppm): 1?, 3.69 (12 H, s, CH3), 3.60 (4H, s, CH2), 7.93 (4H, s, H6); 2,2?-bpy, 7.23 (4H, dd, H5, 3JH-H = 6.0 Hz, 4JH-H = 3.0 Hz), 7.60 (4H, t, H5?, 3JH-H = 7.2 Hz), 7.79 (4H, dd, H6, 3JH-H = 6.0 Hz), 7.94-8.18 (20H, m, H3,H3?,H4,H4?,H6?).

This compound has a wide range of applications. It is believed that with the continuous development of the source of the synthetic route,14871-92-2,(2,2¡ä-Bipyridine)dichloropalladium(II),its application will become more common.

Reference£º
Article; Khutia, Anupam; Shen, Wei-Zheng; Das, Neeladri; Sanz Miguel, Pablo J.; Lippert, Bernhard; Inorganica Chimica Acta; vol. 417; (2014); p. 274 – 286;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

14871-92-2 A common heterocyclic compound, 14871-92-2,(2,2¡ä-Bipyridine)dichloropalladium(II), its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route.

[Pd(bpy)Cl2] (0.10 g, 0.30 mmol) was suspended in water (4 mL). Lactic acid (0.03 g, 0.28 mmol) and 1 M NaOH (0.60 mL) were dissolved in water (10 mL) and then added to the mixture, which was heated under reflux at 150 C with continuous stirring until a clear yellow solution was obtained. The solution was filtered and acetone (10 mL) was added to the solution. The reaction mixture was cooled to 4 C for a long time (2 months), resulting yellow crystals of complex 5. Yield: 33%. m.p.: 250 C. Elemental Anal. Calc. for C13H13ClN2OPd (355.10): C, 44.0; H, 3.7; N, 7.9. Found: C, 44.1; H, 3.6; N, 7.8%. IR (KBr, numax/cm-1): 1634 s, nu(CO); 1621 s, nu(CC); 1496 m, 1443 s, nu(CC,CN). Far-IR (Nujol, numax/cm-1): 333 m, nu(Pd-Cl); 285 m, nu(Pd-C); 243 m, nu(Pd-N). 1H NMR (CDCl3, delta/ppm): 2.40 (s, 3H, c), 3.01 (s, 2H, a), 7.61 (m, 2H, 5,5?), 8.02 (m, 4H, 3,3? and 4,4?), 9.31, 9.51 (2d, 2H, 6,6?).

This compound has a wide range of applications. It is believed that with the continuous development of the source of the synthetic route,(2,2¡ä-Bipyridine)dichloropalladium(II),14871-92-2,its application will become more common.

Reference£º
Article; Balboa, Susana; Carballo, Rosa; Castineiras, Alfonso; Gonzalez-Perez, Josefa Maria; Niclos-Gutierrez, Juan; Polyhedron; vol. 50; 1; (2013); p. 512 – 523;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

A common heterocyclic compound, 14871-92-2,(2,2¡ä-Bipyridine)dichloropalladium(II), its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route. 14871-92-2

General procedure: Palladium(II) chloride (PdCl2), 2,2?-bipyridine (bipy), 1,10-phenanthroline (phen), thiourea (TU, 1), N-methylthiourea (meTU, 2), N-buthylthiourea (buTU, 3), N,N?-diethylthiourea (dietTU, 4) and N,N?-dibuthylthiourea (dibuTU, 5) were purchased as pure reagents at AG, from Sigma Aldrich. Potassium tetrachloropalladate(II) was prepared by the reaction of palladium chloride with a slight excess of potassium chloride. The complexes [Pd(bipy)Cl2] and [Pd(phen)Cl2], were obtained by adding 1 mmol of the respective ligand to 0.326 g (1 mmol) of K2[PdCl4] suspended/dissolved in 40 mL of wet methanol under reflux for about 1 h. The precipitated crystalline powders were recovered by filtration and dried under vacuum for 2 h. 0.25 mmol of these complexes (83 and 89 mg, respectively) were then suspended again in a water/methanol mixture, whereupon 0.5 mmol of the respective thiourea (1-5) was added under reflux. After 1 h, clear yellow to orange solutions were obtained. These solutions were filtrated and the filtrates were kept for 3-5 days at room temperature for crystallization. As a result yellow-red crystals were obtained. The experimental yield of the products, based on Pd, was more than 50%. All the solvents, of analytical grade, were dried and deoxygenated before being used. Elemental analyses were performed at the Microanalytical Laboratory of Redox snc (Milano). Characterization details are extensively quoted in the supplementary material.

This compound has a wide range of applications. It is believed that with the continuous development of the source of the synthetic route,14871-92-2,(2,2¡ä-Bipyridine)dichloropalladium(II),its application will become more common.

Reference£º
Article; Rotondo, Archimede; Barresi, Salvatore; Cusumano, Matteo; Rotondo, Enrico; Polyhedron; vol. 45; 1; (2012); p. 23 – 29;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method

A common heterocyclic compound, 14871-92-2,(2,2¡ä-Bipyridine)dichloropalladium(II), its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route. 14871-92-2

To a yellow suspension containing 0.10 g (0.31 mmol) of [Pd(bpy)Cl2] in water (10 mL) wereadded a solution containing 0.04 g (0.32 mmol) of HaptHCl in water (10 mL) and an aqueoussolution of NaOH (0.25 M, 2.5 mL). When the mixture was stirred at 50 C for 3 h, the suspensionturned to a yellow solution. After filtration, a saturated aqueous solution of NaNO3 (5 mL) wasadded to the yellow filtrate. The mixture was stood at room temperature for 2 d, and the resultingyellow crystals of [2](NO3)2 was collected by filtration. Yield: 0.03 g (36%)., 14871-92-2

This compound has a wide range of applications. It is believed that with the continuous development of the source of the synthetic route,14871-92-2,(2,2¡ä-Bipyridine)dichloropalladium(II),its application will become more common.

Reference£º
Article; Kouno, Masahiro; Miyashita, Yoshitaro; Yoshinari, Nobuto; Konno, Takumi; Chemistry Letters; vol. 44; 11; (2015); p. 1512 – 1514;,
Chapter 1 An introduction to palladium catalysis
Palladium/carbon catalyst regeneration and mechanical application method